Model of transient creep for a ferritic-martensitic steel based on the modified θ-projection method

封面

如何引用文章

全文:

开放存取 开放存取
受限制的访问 ##reader.subscriptionAccessGranted##
受限制的访问 订阅或者付费存取

详细

The paper presents the developed model for predicting the behavior of a ferritic-martensitic steel during all creep stages. A modified θ-projection method is proposed as a solution. The main advantages of the method are abilities to model creep curves for a wide range of temperatures and stresses (which reduces the need for long-term run tests); to validate calculations by determining time to failure; to predict a steady-state creep rate. Despite the usefulness of the proposed approach, certain limitations are noted that result in modeling uncertainties. Higher accuracy and robustness can be achieved using a "mechanical equation of state equation" model of Rabotnov type.

全文:

受限制的访问

作者简介

А. Kolotovkina

Academician A.A. Bochvar High-Tech Research Institute of Inorganic Materials

编辑信件的主要联系方式.
Email: AVKolotovkina@bochvar.ru
俄罗斯联邦, Moscow, 123098

V. Zborovskii

Lebedev Physical Institute of the Russian Academy of Sciences, Troitsk Branch; National Research Center “Kurchatov Institute”

Email: AVKolotovkina@bochvar.ru
俄罗斯联邦, Troitsk, Moscow, 108840; Moscow, 123182

M. Leonteva-Smirnova

Academician A.A. Bochvar High-Tech Research Institute of Inorganic Materials

Email: AVKolotovkina@bochvar.ru
俄罗斯联邦, Moscow, 123098

参考

  1. ASME Boiler & Pressure Vessel Code, Section III – Rules for Construction of Nuclear Facility Components – Section II – Part D Properties (Customary). ASME 2019 Edition.
  2. Сапунов В.Т. Прогнозирование ползучести и длительной прочности жаропрочных сталей и сплавов ЯЭУ. М.: НИЯУ МИФИ, 2015. 136 с.
  3. Riedel H. Fracture at High Temperature. Berlin: Springer, 1987. 418 p.
  4. Булыгин И.И., Голубовский Е.Р., Трунин И.И. Прогнозирование характеристик ползучести сплавов для ГТД // Проблемы прочности. 1978. № 6. С. 19–21.
  5. Работнов Ю.Н. Ползучесть элементов конструкций. М.: Наука, 1966. 753 с.
  6. Качанов Л.М. Теория ползучести М.: ФИЗМАТЛИТ, 1960. 455 с.
  7. Evans R., Parker J., Wilshire B. Recent advances in creep and fracture of engineering materials and structures. B. Wilshire and D.R.J. Owen. Pineridge Press, 1982. 135.
  8. Evans R. Statistical scatter and variability of creep property estimates in θ projection method // Mater. Sci. Technol. 1989. V. 5. P. 699–707.
  9. ГОСТ 10145–81. Металлы. Метод испытания на длительную прочность.
  10. Jeyaraj A., Vijayanand V.D., Ganesan V. Grain size effect on creep properties of 304HCu SS and modelling of creep curves using modified theta projection approach // Trans. Ind.National Academy of Engineering. 2021. V. 10.
  11. Peng Yu, Weimin Ma. A modified theta projection model for creep behavior of RPV steel 16MND5 // J. Mater. Sci. Techn. 2020. V. 47. P. 231–242.
  12. Evans M. Sensitivity of the theta projection technique to the functional form of the theta interpolation/extrapolation function // J. Mater. Sci. 2002. V. 37. P. 2871–2884.
  13. Деммель Дж. Вычислительная линейная алгебра. М.: МИР, 2001. 430 с.
  14. Perez J. An alternative method of calibration and prediction for the theta-projection model // ETD Collection for University of Texas. 2019. V. 69.
  15. Srinivasan V., Vanajal J., Choudhary B. Modeling of creep deformation behaviour of RAFM steel // Trans. Ind. Institute of Metals. 2016. V. 69. P. 567–571.

补充文件

附件文件
动作
1. JATS XML
下载
2. Fig. 1. Experimental creep curves from the experimental base and the corresponding approximated curves calculated according to (1).

下载 (482KB)
索引源数据
3. Fig. 2. Dependences of the final actual values ​​of the coefficients θi(i = 1–4) on the stress σ and temperature T, as well as their approximate functional dependencies: a – coefficient θ1; b – coefficient θ2; c – coefficient θ3; d – coefficient θ4.

下载 (299KB)
索引源数据
4. Fig. 3. Dependences of the steady-state creep rate ε̇ stat on the stress σ and temperature T, as well as the approximate functional dependence.

下载 (102KB)
索引源数据
5. Fig. 4. Dependences of the creep time to failure τR on the stress σ and temperature T of the obtained creep rates ε̇ stat.

下载 (88KB)
索引源数据
6. Fig. 5. Scatter plot of experimental and calculated values ​​of creep time to failure τR .

下载 (87KB)
索引源数据
7. Fig. 6. Experimental and simulated creep curves for the same values ​​of stress σ and temperature T: a – 40 MPa, 943 K; b – 100 MPa, 943 K; c – 50 MPa, 923 K; g – 100 MPa, 923 K; d – 75 MPa, 923 K; f – 14(13) MPa, 1073 K; g – 400 MPa, 773 K; h – 440 MPa, 773 K.

下载 (551KB)
索引源数据
8. Fig. 7. Modeled and closest experimental creep curves in terms of the combination of stress σ and temperature T.

下载 (273KB)
索引源数据